Liquefied Petroleum Gas, LPG, LPG exporter, LPG producer, Iran LPG, LPG Iran, Liquefied Petroleum Gas exporter, Petro Oil, petrochemical, petrochemical exporter

Liquefied Petroleum Gas (LPG)



MGT PetrOil Company as a major producer, supplier and exporter of several petrochemical products in the Middle East, is located in Iran. MGT PetrOil Company is highly experienced in exporting and is active in case of Liquefied Petroleum Gas (LPG) supplying.

 

Iran holds the world's fourth-largest proved crude oil reserves and the world's second-largest natural gas reserves. Iran also ranks among the world's top 10 oil producers and top 5 natural gas producers. The Strait of Hormuz, off the southeastern coast of Iran, is an important route for oil exports from Iran and other Persian Gulf countries. Liquefied natural gas (LNG) volumes also flow through the Strait of Hormuz.

National Petrochemical Company (NPC) was established in 1963 to spearhead the development and policy-making for Iran’s petrochemical industry. Iran’s petrochemical industry is the oldest in the Middle East and in ethylene production it is the second oldest after Turkey. During 1964-1977 Razi, Abadan, Pazargad, Ahwaz carbon black, Kharg, Farabi and Shiraz expansion projects were completed.

                                                          

Iran as a prominent name in oil and gas industries, has been producing Liquefied Petroleum Gas (LPG) in its enormous and well-equipped petrochemical complexes and has undeniable ability in case of supplying this product for exporting.

 

What is LPG?

LPG - Liquefied Petroleum Gas is a definition of gases produced by wet gas or raw oil. The LPG gases are taken out of the raw oil during refining, or from natural gas separation. LPG gases are defined as propane, butane and a mixture of these. Large atmospheric pressure gas carriers carry most of the LPG transported at sea. However, some LPG is transported with intermediate pressure gas carriers. Fully pressurized gas carriers mainly handle coastal trade.

LPG can be cooled with water, and most LPG carriers have direct cargo cooling plants that condenses the gas against water.

The sea transport of LPG is mainly from The Persian Gulf to Japan and Korea. It is also from the north- west Europe to USA, and from the western Mediterranean to USA and Northwest Europe. LPG is utilized for energy purposes and in petrochemical industry.

 

The Chemistry of LPG

Atoms of hydrogen (H) and carbon (C) combine to form hydrocarbon molecules which can be made up of different numbers of hydrogen and carbon atoms, hence the term ‘hydrocarbon’.

A molecule containing three carbon atoms and eight hydrogen atoms is called propane:

 

Fig 1. Molecule of propane (C3H8)

 

In a like manner, four carbon atoms bonded to 10 hydrogen atoms forms butane:

 

LPG

Fig 2. Molecule of butane (C4H10)

 

There are two possible configurations for the butane molecule. The above arrangement consists of a straight C-chain and is called normal butane or n-butane. If the C-chain is branched, it is called iso-butane. Such a re-arrangement of the atoms is known as isomerization and has no significant effect on the fuel properties.

Hydrocarbons with single carbon bonds are known as saturated hydrocarbons while those with double or triple bonds are unsaturated hydrocarbons. Examples of saturated hydrocarbons are methane (CH2), ethane (C2H6), propane (C3H8) and butane (C4H10). Unsaturated hydrocarbons include ethylene (C2H4), propylene (C3H6), butylene (C4H8) and acetylene (C2H2).

 

Physical Properties of LPG

The properties of LPG mixtures can usually be calculated from the properties of the individual constituents (propane, butane, etc.) provided the proportions of the constituents are known. Following is a description of the most important physical properties of LPG mixtures.

 

3.1 Density

The density of LPG is defined as its mass per unit volume (kg/l) at a given temperature. LPG liquid has a density of about 0,54 kg/l at 15C and is therefore lighter than water.

It varies slightly with LPG composition and every batch of LPG produced at a refinery will have a specified density at a given temperature. LPG liquid is fairly light - about half the weight of water. To convert liters of LPG to kilograms, simply multiply the number of liters by the density.

LPG vapour has a density of about 1,9 times that of air and is therefore heavier than air. This is important when considering ventilation requirements and has an influence on the design of burners and certain meters for measuring vapour flow.

Buildings used for storing LPG cylinders must have adequate floor level ventilation; in the event of a leak, the vapour being heavier than air will flow along the ground to the lowest level and remain there for a considerable period of time, and can be an explosion hazard.

 

3.2 Calorific Value (CV)

All substances which burn generate energy in the form of heat, which varies in quantity with the nature of the substance. The total amount of heat liberated by burning a substance is known as its Calorific Value or CV. It is usually expressed in megajoules per kg (MJ/kg). For LPG, it is 49,6 MJ/kg.

 

3.3 Thermal rate of expansion (expansion and contraction)

The thermal rate of expansion of liquid LPG is about 10 times that of water and since liquids cannot be compressed, it is probably the most important property of LPG affecting the way the gas is stored, handled and filled. Storage tanks and portable cylinders filled to allow for an ullage space in the vessel and cylinders must never be filled to more than about 85% of the internal volume.

When the valve of an LPG is opened, the pressure inside the cylinder is reduced and the liquid starts to vaporise (boil) at lower pressure. This vaporisation of the gas causes cooling to occur and the temperature of the gas will decrease. If the gas off-take rate is too high, the gas temperature will decrease to below 0⁰C and ice will start to form on the lower outside wall of the cylinder. Because LPG contains propane and butane, with boiling points of –42,1⁰C and – 0,5⁰C respectively, the mixture begins to separate – propane continues to boil off while the butane remains in liquid form at temperatures below its boiling point of –0,5⁰C. To avoid this situation, vaporiser units are used for LPG or pure propane can be used instead of Handigas (butane/propane mixture). It should be noted that low winter temperatures will aggravate this situation.

 

3.4 Vapour pressure

One liter of liquid Handigas will rapidly and totally vaporise when exposed to atmospheric pressure (100 kPa) to form about 275 liters of vapour at 15⁰C. In a closed cylinder containing some liquid Handigas, a relatively small quantity will vaporise in the restricted volume of the cylinder, to produce a cylinder pressure of about 250 kPa at 0⁰C. This closed cylinder pressure is equal to the vapour pressure, and it increases dramatically with temperature to 500 kPa at 20⁰C and 1 550 kPa at 60⁰C.

A liquid leak is far more serious than a gas leak due to the high volume of gas formed. This is why cylinders must always be stored, transported and used in the upright position. In air a gas leak will form a highly flammable mixture of about 10 000 liters from one liter of liquid gas. As LPG consists of a mixture of propane and butane and since propane has a much higher vapour pressure than butane, the vapour pressure in a cylinder containing mostly propane will be much higher than that of a cylinder containing mostly butane. This relationship between pressure and temperature of pure propane and butane, and LPG (60:40 mix) is illustrated below.

 

LPG Production

Conventional Technology

Natural gas processing begins at the wellhead. The composition of the raw natural gas extracted from producing wells depends on the type, depth, and location of the underground deposits and the geology of the area. The natural gas produced from oil wells is generally classified as “associated-dissolved,” meaning that the natural gas is associated with or dissolved in crude oil. Natural gas production without any association with crude oil is classified as “non-associated.” About 60% of the world supply of LPG comes from associated gas processing, and 40% of the LPG is produced in oil refineries from crude distillation, fluid catalytic cracking units, hydrocrackers, etc.

There are 4 columns used in the conventional process. First stage of LPG extraction from NGL is DeEthanizer. In the DeEthanizer column, methane and ethane are expected to be separated and flow through the top of the column. Since there is no requirement to liquefy methane and ethane, especially in small amounts, these components will be kept in vapor phase and additional condenser is unnecessary.

In this DeEthanizer, 100% methane and ethane in mixed feed can be separated and leaves the top of the column. This product will be used internally as a fuel to generate the steam which is used for reboiler of the column. Heat is supplied to the column by forced circulation using reboiler pump to reboiler and into the column. The heavier hydrocarbons other than ethane leave the column as bottom product in a liquid phase. Next it is sent to DeButanizer column.

DeButanizer is used instead of DePropanizer because the bottom product of DeEthanizer composed of small amount of propane (2 % of mass fraction) and butane (5 % of mass fraction). So that smaller columns will be used for next extraction. This is for economic reason and the efficiency of the separation as it is easier to extract the product this way and less duty will be required for reboiler.

Before entering DeButanizer column, the DeEthanizer bottom product is expanded from 26 - 17 bar and fed into DeButanizer as mixed-phase feed. This feed is fractionated into mixed propane and butane as overhead product and heavier hydrocarbons (C5+) as bottom product. Then the overhead product is totally condensed in the condenser by heat exchange with cooling water, and condensate is collected in reflux drum. The reflux drum should be used in order to prevent cavitation on the pump due to vapor phase. The DeButanizer reflux and product pump serve the dual purpose of supplying reflux to the column and allowing withdrawal of column overhead product butane from the reflux drum. The column heat is supplied by a reboiler and circulation is aided by DeButanizer reboiler circulating pump.

About 100% propane and 99% butane can be recovered from the feed at the overhead column product. This stream leaves the column and is sent to DePropanizer column to separate propane and butane. Meanwhile, the bottom product composed of pentane and heavier hydrocarbons will be stored as natural gasoline. Since the bottom product has high temperature (> 200⁰C), it will be cooled by heat exchanger before being sent to the storage.

Propane and butane stream is expanded from 16 - 10 bar and enters the DePropanizer as mixed-phase feed. The DePropanizer separates propane as overhead product and butane as bottom product. Condenser is used to totally condense the overhead vapor from DePropanizer. Condensate is collected in DePropanizer column reflux drum. A part of the condensed overhead product is sent back to the column as reflux via pump while the remaining part is withdrawn as a liquid propane product. DePropanizer reboiler heat is supplied by reboiler. Reboiler circulation is aided by reboiler circulation pump.

It is about 99.9% of propane can be recovered as top product and 99.9% of butane is recovered as bottom product. The butane product is field grade butane which is composed of 30% i-butane and 65% n-butane. This is next being sent to butane splitter to get i-butane and n-butane products separately, since it could be sold with higher price than field grade butane.

 

Liquefied Petroleum Gas

Fig 3. Process flow diagram of LPG unit

 

The field grade butane is expanded from 10 - 5 bar before enter the butane splitter. i-butane is recovered as overhead product and n-butane as bottom product. I-butane is totally condensed by condenser. Condensate is collected in reflux drum. A part of the condensed overhead product is sent back to the column as reflux via pump while the remaining part is withdrawn as a liquid i-butane product. Butane splitter heat is supplied by reboiler. Reboiler circulation is aided by reboiler circulation pump. Butane splitter column separates 96% mole of i-butane in the overhead product and 96% mole of n-butane in the bottom product. Both products have higher price than field grade butane.

 

LPG Usages

Application of LPG varies from food to transport industry. Its consumption depends on the local market conditions. LPG is widely used in the Food Industry like hotels, restaurants, bakeries, canteens, resorts etc. Low sulphur content and controllable temperature makes LPG the most preferred fuel in the food industry.

 

Glass & Ceramic

The manufacture of glass / ceramic products is complicated by numerous chemical reactions which occur during the process. The use of a clean fuel like LPG enhances the product quality thereby reducing technical problems related to the manufacturing activity. LPG being a gaseous fuel gets easily regulated and complements the heating process.

 

Building Industry

LPG being a premium gaseous fuel makes it ideal for usage in the Cement manufacturing process. The ease in regulation and soft quality of the LPG flame and low sulphur content are the key advantages both with regard to cement quality and kiln operability.

 

Metal Industry

The metal industry is indeed one of the most important consumers of energy. LPG being a far superior fuel as compared to the other heavy fuels helps improve the cost of operation and strikes an economic balance between fuel price and quality of the end product. The application is basically for cutting, heating and melting. Both ferrous and non-ferrous metals are frequently cast into shapes by melting and injection or pouring into suitable patterns and moulds. LPG in this case is an ideal fuel for meeting the requirement of temperature regulation and desired quality.

 

Farming Industry

LPG is the ideal fuel for production of food by agriculture and animal husbandry. Drying of crops and other farm products requires clean and sulphur free fuel for drying activity to avoid any transfer of bad taste or smell to the dried crops.

 

Aerosol Industry

An aerosol formulation is a blend of an active ingredient with propellant, emulsifiers, perfumes, etc. LPG, being environment friendly, has replaced the ozone depleting CFC gases which were earlier used by the aerosol Industry.

 

Automotive Industry

Automotive LPG is a clean fuel with high octane, aptly suited for vehicles both in terms of emissions and cost of the fuel. The main advantage of using automotive LPG: it is free of lead, very low in sulphur, metals, aromatics and other contaminants. Unlike natural gas, LPG is not a Green House Gas. The following table lists the preferred LPG composition in Europe.

 

  Country

Propane

Butane

  Austria

50

50

  Belgium

50

50

  Denmark

50

50

  France

35

65

  Greece

20

80

  Ireland

100

0

  Spain

30

70

  Sweden

95

5

  United Kingdom

100

0

  Germany

90

10

 

Table 1. LPG Composition (% by Volume) as Automotive Fuel in Europe (West Virginia University)

 

Cogeneration using LPG

LPG is an ideal fuel for electricity & heat / electricity and comfort cooling. This finds varied applications in industries requiring power and steam, power and hot air. LPG is ideally suited for shopping malls, offices requiring power and air conditioning.

LPG has lower calorific value then petrol, so it provides less miles per gallon, however in European countries LPG tax levels are much lower than both diesel and unleaded so it is still a far more cost effective way to run your car. The tax break is due to evidence that suggests that LPG is better for the environment than the mainstream fuels.


Contact Us

Phone:+98 21 88 63 5592
Fax: +98 21 88 63 5568
Email: Info@mgtpetroil.com